Commercial Electric CER6041WH30 Manual de Instruções descarregar pdf

WARNING - RISK OF ELECTRIC SHOCK.

DISCONNECT MAIN POWER AT FUSE OR

CIRCUIT BREAKER BEFORE INSTALLING OR

SERVICING THE FIXTURE.

LED 6” RETROFIT TRIM INSTALLATION

INSTRUCTIONS - MODEL CER6741A

QUESTIONS? CALL TOLL

FREE 1-800-345-0542

REV 05-AUG-14

Please read carefully and save these instructions, as you

may need them at a later date.

GENERAL: All electrical connections must be in accordance with local and

National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper

electrical wiring connections obtain the services of a qualified electrician.

Remove the trim from the box and make sure that no parts are missing by

referencing the PARTS illustrations.

THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LED

LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE

DETERMINED BY CSA OR CANADIAN AUTHORITIES HAVING

JURISDICTION.

__________________________________________

WARNING- RISK OF FIRE OR ELECTRIC SHOCK

FOR USE WITH HOUSING MODELS: INCANDESCENT HOUSINGS –

COMMERCIAL ELCETRIC C7IC, C7ICR, C7ICA, C7ICRA, C7, C7R, C7S,

HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT, H7RICAT, H7T, H7RT,

H27ICT, H27T, H27RT, H750ICAT, H750RICAT; CORDELIA HBR7LICAT,

HBR7LICRAT; CAPRI CR1, CRR1; ELCO EL7ICA, EL7RICA; JUNO IC22,

IC22R; THOMAS PS1, PS1-RM; DMF DH6ICATQ, DH6ICRATQ; NORA

NHIC-17QAT, NHRIC-17QAT; ELITE B6IC, B6RIC; SEA GULL 11018,

11028. HALO LED HOUSINGS – H750ICAT, H750RICAT.

• Do not alter, relocate, or remove wiring, lampholders, power supply, or any

other electrical component. Installation of the retrofit assembly requires a

person familiar with the construction and operation of the luminaire’s

electrical system and the hazard involved. If not qualified, do not attempt

installation. Contact a qualified electrician.

• Do not make or alter any open holes in an enclosure of wiring or electrical

components during kit installation.

• To prevent wiring damage or abrasion, do not expose wiring to edges of

sheet metal or other sharp objects.

_____________________________

ASSEMBLY AND INSTALLATION

1. If the installed housing does not have TORSION SPRING SLOTS or

C-CLIPS (FIG. 5), then remove the SCREWS securing the TORSION

SPRINGS to the HEATSINK. Attach the FRICTION BLADES (included) to

the same location using the SCREWS that were previously removed.

(FIG. 7)

INCANDESCENT HOUSINGS

1. Unscrew the WING NUT inside the CAN to detach the SOCKET

BRACKET from the CAN. Disengage the SOCKET from the SOCKET

BRACKET. (FIG. 2)

2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 3)

3. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the MALE

CONNECTOR of the SOCKET ADAPTER ASSEMBLY. (FIG. 4)

4. If using TORSION SPRINGS, squeeze both TORSION SPRING arms

together and insert into the TORSION SPRING SLOTS (or RECEIVER

BRACKETS) of the CAN. (FIG. 5)

5. Tuck all wires into the CAN and carefully push the RETROFIT TRIM into

CAN. (NOTE: To provide enough room in shallow cans, carefully position

SOCKET ADAPTER and SOCKET adjacent to the long side of the LED

DRIVER prior to inserting the RETROFIT TRIM into the CAN.) (FIG. 5)

LED HOUSINGS

1. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the MALE

CONNECTOR of the HALO HOUSING. (FIG. 4)

2. If using TORSION SPRINGS, squeeze both TORSION SPRING arms

together and insert into the TORSION SPRING SLOTS (or RECEIVER

BRACKETS) of the CAN. (FIG. 5)

3. Tuck all wires into the CAN and carefully push the RETROFIT TRIM into

CAN. (NOTE: To provide enough room in shallow cans, carefully position

SOCKET ADAPTER and SOCKET adjacent to the long side of the LED

DRIVER prior to inserting the RETROFIT TRIM into the CAN.) (FIG. 5)

FACEPLATE REPLACEMENT (OPTIONAL)

This product is designed to allow the user to easily replace the magnetically

attached DECORATIVE FACEPLATE of the RETROFIT TRIM.

1. Pull off the FACEPLATE from the RETROFIT TRIM. (FIG. 6)

2. Attach the replacement FACEPLATE onto the RETROFIT TRIM. (FIG. 6)

5 in. – 7 in.

6 in.

PARTS

SOCKET ADAPTER

ASSEMBLY

RETROFIT TRIM

COMPATIBLE HOUSING

DIMENSIONS

FIG. 6

FIG. 2

FIG. 4

FIG. 3

FIG. 5

FIG. 7

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - 1-800-345-0542

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.LED 6” RETROFIT TRIM IN

Página 2 - FIVE-YEAR LIMITED WARRANTY

________DIMMINGDimming performance may depend on the dimmer, the dimmerrange adjustment setting (for dimmers with brightness rangeadjustments), the wi

Página 3 - CER6741A

REV 05-AUG-14ADVERTENCIA: RIESGO DE DESCARGA ELÉCTRICA. DESCONECTE EL SUMINISTRO ELÉCTRICO DE LA CAJA DE FUSIBLES O LOS INTERRUPTORES DE CIRCUITO ANTE

Página 4 - REEMPLAZO DE CONTROLADOR

Página 5 - 12,7 – 17,78 cm

AVERTISSEMENT – RISQUE DE DÉCHARGE ÉLECTRIQUE. COUPEZ LE COURANT AU NIVEAU DU DISJONCTEUR OU DE LA BOÎTE DE FUSIBLES AVANT D’INSTALLER OU D’EFFECTUE

Página 6 - ATTENTION: